Fusion MS-UD650 Installation Bedienungsanleitung PDF herunterladen

Fusion

™

MS-UD/AV650/750 Installation

Instructions

Important Safety Information

WARNING

Failure to follow these warnings and cautions could result in

personal injury, damage to the vessel, or poor product

performance.

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install

this product.

Before applying power to this product, make sure it has been

correctly grounded, following the instructions in the guide.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation,

contact Fusion Product Support.

What's In the Box

• Two Mounting plates

• Mounting hardware

◦ Four 8-gauge, self-tapping screws

◦ Four M4 machine screws

• Power and speaker wiring harnesses

• RCA splitter

• Micro-USB to USB cable (UD models only)

• Lightning

™

connector to USB cable (UD models only)

• Apple

30-pin to USB cable (UD models only)

• Remote control (AV models only)

• Two AAA batteries (AV models only)

Tools Needed

• Phillips screwdriver

• Electric drill

• Drill bit (size varies based on surface material and screws

used)

• Rotary cutting tool or jigsaw

• Marine sealant (optional)

Mounting Considerations

• The stereo must be mounted in a location where there is

enough clearance for the open door of the stereo as

indicated on the template.

• The stereo must be mounted in a location that allows open

airflow around the rear of the stereo for heat ventilation.

• The stereo must be mounted within 45° of the horizontal

plane.

•

The cable should have a drip loop to allow water to drip down

off the cable and avoid damaging the stereo.

• If you want to mount the stereo outside the boat, it must be

mounted in a location well above the waterline, where it is not

submerged.

• If you want to mount the stereo outside the boat, it should be

mounted in a location where it will not be damaged by a

docks, pilings, or other pieces of equipment.

• To avoid interference with a magnetic compass, the stereo

should be installed at least 15 cm (5.9 in.) away from a

compass.

Mounting the Stereo

NOTICE

Be careful when cutting the hole to flush mount stereo. There is

only a small amount of clearance between the case and the

mounting holes, and cutting the hole too large could

compromise the stability of the stereo after it is mounted.

Before mounting the stereo, you must choose a location

following the guidelines above.

Trim the template and make sure it fits in the selected

location.

Secure the template to the selected location.

Using a drill bit appropriate for the mounting surface, drill the

hole inside the corner of the dashed line on the template to

prepare the mounting surface for cutting.

Using a jigsaw or rotary tool, cut the mounting surface along

the inside of the dashed line indicated on the template.

If necessary, remove the sun cover from the stereo.

Place the stereo in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

After the stereo fits correctly in the cutout, ensure the

mounting holes on the stereo line up with the pilot holes on

the template.

If the mounting holes on the stereo do not line up, mark the

new pilot-hole locations.

Using an appropriately sized drill bit for the mounting surface

and screw type, drill the pilot holes.

Remove the template from the mounting surface.

Connect the wiring harnesses and wires, while observing

polarity.

Place the mounting gasket on the back of the stereo

December 2014

Printed in Taiwan 190-01759-02_0A

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - Instructions

®Fusion™ MS-UD/AV650/750 Installation InstructionsImportant Safety Information WARNINGFailure to follow these warnings and cautions could result in pe

Seite 2 - Connection Considerations

14If necessary, place the nut plates Á behind the dashboard.15Place the stereo in the cutout.16Secure the stereo to the mounting surface using the inc

Seite 3

2Connect the black wire to the negative (-) battery terminal.3Select an option:• Connect the yellow wire to the positive (+) battery terminal, and rou

Seite 4 - Stereo Information

ÄWater-tight connectionsÅRemote onNMEA 2000 System Wiring DiagramÀStereoÁSupported chartplotter MFDÂFusion Wired remote, such as the NRX200iÃIn-line s

Seite 5 - 28 mm (1.08 in.)

À52 mm (1.37 in.)Á177 mm (6.97 in.)Â28 mm (1.08 in.)Registering Your Fusion MS-UD/AV650/750Help us better support you by completing our online registr

Seite 6

Garmin®, the Garmin logo, and the Fusion™ logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Fusion, F